Vegas Floorboard question - Victory Forums - Victory Motorcycle Forum
 3Likes
  • 1 Post By visionjohnny
  • 2 Post By Tenax
 
LinkBack Thread Tools Search this Thread Display Modes
post #1 of 4 (permalink) Old 10-11-2018, 11:34 AM Thread Starter
Junior Member
 
unxpected12's Avatar
 
Join Date: Oct 2018
Location: South Texas
Posts: 6
Garage
Default Vegas Floorboard question

Hello I had 2 questions regarding converting floorboards on my Vegas to pegs and a noise coming from my primary area.

I took the floorboard off and used a passenger rear peg to see if it would work but didn't... there is no support to hold up peg straight. Has anyone had any success in putting certain pegs in the spot of the board and worked properly. If so please reference what was used. I don't like the look of the big floor boards and the whole heal toe shifter deal. Did a search already for my last resort ...... to buy the mounts and all to switch but they are pricey. Looking for something that would work.

Second I took my bike out yesterday and noticed the while shifting the gears there was a loud gear noise. I have seen vids on YouTube of it but on some it was when the clutch lever was pressed. On my it is when you barley taps the gear lever either up or down. I have to be forceful on and off it. Other than that it ride and shifts all gears great. Clutch is great. I heard and read that the torque compensator nut and clutch nuts come loose and because misaligned. People say its common but I found a vid where someone actually fixed it.Can someone point me in the right direction and the how 2s to get it right ...photos of which one require re-torqueing . Already ordering my primary gasket kit and Loctite. Thanks.

Last edited by unxpected12; 10-11-2018 at 06:41 PM.
unxpected12 is offline  
Sponsored Links
Advertisement
 
post #2 of 4 (permalink) Old 10-11-2018, 02:04 PM
Senior Member
 
visionjohnny's Avatar
 
Join Date: Sep 2010
Location: minnesota
Posts: 12,946
Default

you left words out so I'll try.
For the foot pegs go to HD and tell them you want the spring washers that hold foot pegs up. Take a photo of my post to show them. The spring washers goes between peg and mount can be a bitch on some pegs to get in.
doesn't the heel shifter have two bolts on the back side to unbolt the heel part
Attached Images
File Type: jpg ZZ58039_A.jpg (66.9 KB, 2 views)
unxpected12 likes this.

2008 Vision
Mpls, MN.

Please add your state and model of bike you have. Click user CP @ top of page and then far left click edit signature. Thanks
visionjohnny is offline  
post #3 of 4 (permalink) Old 10-11-2018, 04:49 PM
Senior Member
 
Join Date: Apr 2018
Posts: 302
Default

https://www.denniskirk.com/drag-spec...rd/H273012.sku

I've bought these. Lots of places sell them, probably cheaper than a Harley store sells for. The ones I bought were like 10 per pack. Might have been kuryakyn ones. Cheap and same thing. Work dandy. I put the rounded side towards the peg itself. Thats the way stock ones were on my pegs. They will work either way.
visionjohnny and unxpected12 like this.

2016 Victory Magnum
Lloydz air filter
Ragin Cajun slipons
PowerVision CX
Tenax is offline  
Sponsored Links
Advertisement
 
post #4 of 4 (permalink) Old 10-11-2018, 06:45 PM Thread Starter
Junior Member
 
unxpected12's Avatar
 
Join Date: Oct 2018
Location: South Texas
Posts: 6
Garage
Default

thank you for the info. the heal toe shift is 1 solid piece just like on the kingpin. i did unscrew the rear toe peg and it helps a bit.
unxpected12 is offline  
Sponsored Links
Advertisement
 
Reply

Quick Reply
Message:
Options

Register Now



In order to be able to post messages on the Victory Forums - Victory Motorcycle Forum forums, you must first register.
Please enter your desired user name, your email address and other required details in the form below.

User Name:
Password
Please enter a password for your user account. Note that passwords are case-sensitive.

Password:


Confirm Password:
Email Address
Please enter a valid email address for yourself.

Email Address:
OR

Log-in










Thread Tools Search this Thread
Show Printable Version Show Printable Version
Email this Page Email this Page
Search this Thread:

Advanced Search
Display Modes
Linear Mode Linear Mode



Posting Rules  
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off
Trackbacks are On
Pingbacks are On
Refbacks are On

 
For the best viewing experience please update your browser to Google Chrome